Vapolution is another Vaporizer that has acquired a lot of popularity among those who indulge in vaporization. A portable vaporizer that provides you with a healthy alternative to smoking. The vaporizer also warms the herbal substance and gives out the ingredients that are least harmful and do not cause any alarming side effects.

Follow the instructions below and be assured of an amazing experience

1. Put the herbal material at the end closest to the dimple in the straight bowl. Now attach the end that is far from the dimple to the tubing. The dimple acts like a screen. If there is some difficulty in fitting the bowl into the tubing then submerge it into the boiling water for 3-5 seconds. It will make the bowl easily slip into the boiling water.
2. Now slide the white retaining washer over the straight bowl, so that it touches the food-grade tubing.
3. After this, very carefully insert the bowl in the top of the vaporizer. The bowl will continue to slip through until it touches the bottom of the heater. The washer should be positioned in a way that it prevents the bowl from directly touching the bottom heater. There should be a gap of 1/4″ from the heater.
4. Now carefully plug in the cord to a power supply socket or car adapter or the optional battery pack. This cord should now be plugged into the power jack on the back of the vaporizer. The vaporizer now receiving power supply can be switched on.
5. Turn the switch on. A light will illuminate.
6. The Vaporizer has to be pre-heated for sometime. The lowest temperature of the Vapolution Vaporizer is at 6 O’clock and the highest is at 4 O’clock. After 5 minutes of pre-heating, turn the vaorizer to your preferred setting, usually the setting at 12 O’clock is recommended. One of the many advantages of a Vapolution Vaporizer is that it is designed to continue working for 8 hours without overheating or burning out. Experienced users leave the Vaporizer on at their preferred setting all the time.
7. It is a usually advised that you should finely grind the herbs before loading them into the bowl. However, in case of a Vapolution Vaporizer, instead of grinding break up the plant pods in 1-3 small pieces. Roll the pods between your fingers and mold them into a pellet. Gently put the vapor pellet into the bowl. Do not make the pellet too big as then it will hamper the airflow and a good vapor would not be possible. If the pellet is too small then there is a very likely chance that it will fall out. Although loading is a procedure that requires practice but once learned, the vapor formed would be close to perfection.
8. After loading the bowl, place the loaded material on top of the pre-heated vaporizer. Now slowly and steadily start drawing the vapors in. Keep on drawing the vapor until you are out of breath. Hold the vapor in and then exhale. A visible vapor will rise. Repeat this process for 3-7 times. The vapor produced also depends on the quality of your herbs and the temperature that you have set.

The safe zone on the vaporizer is the temperature setting at which rarely will the herbs burn. This safe zone is from 10 O’clock to 12 O’clock. A user should not divulge much from the safe zone temperature setting until he or she has acquired enough experience to handle higher temperature settings. The herbs change the their colors during the process of vaporization. It turns from golden to dark brown gradually and later if kept on heat for too long to a black pellet. It will turn black only on settings above 2 O’clock. This temperature can also cause vapor choke. Hence avoid this setting.

Blow through the tube for cleaning the vaporized herb. Keep the bowl into a receptacle and blow so that the residue gets collected into the receptacle and the tube becomes empty. Wait for 30 minutes to 1 minute for the bowl to cool.

Maintenance

Maintaining the Vaporizer is very significant and the efficiency of any vaporizer depends upon maintenance. Clean the bowls by submerging them into rubbing alcohol for 8-12 hours and rinse with warm water. After allowing the vaporizer to cool for 30 minutes and then put a Q-tip in rubbing alcohol and clean out the heater receptacle. You can repeat the procedure if necessary. A dry Q-tip should be used to clean out the residue that remains attached to it. The tube becomes yellow after use and hence should either be replaced or cut short. Maintaining the vaporizer is not as difficult as it might appear, only consistency is required. Consistent cleansing will lead to better and efficient performance of the Vaporizer. Also bear in mind that, never force the bowl into the vaporizer as it can lead to breaking of the glass heater.

This entry was posted on Wednesday, September 24th, 2008 at 5:03 am and is filed under Instructional. You can follow any responses to this entry through the RSS 2.0 feed. Both comments and pings are currently closed.