The Volcano Vaporizer exceeds every other unit in the market in terms of efficiency, performance and quality. It spearheads the range of revolutionary vaporizers that have recently swarmed the market. Adorned with latest technology, the Volcano Vaporizer is one of the best devices which provides the ultimate vaporization experience ever. Different flavors and essences are extracted from herbal substances at controlled temperature of maximum 230°C/ 446°F. Vapors formed hence, can be inhaled without worrying about the harmful effects. The biggest advantage of using a vaporizer is that there is no combustion involved. Combustion results in formation of toxic-substances, inhalation of which results in deterioration of different systems of physiology. Carbonization is another consequence of combustion that causes irritation of the respiratory tract and produces noxious odors.

Further, heating the material at high temperatures such as (500-700°C;932-1292°F) completely annihilates the original flavor and essence that is present in the plant. As a result, almost all the relevant ingredients are destroyed and what is left should not be inhaled.

Following instructions describe how an Easy Valve Volcano should be used and how should the Solid Valve Volcano be used.

Easy Valve Volcano Vaporizer – Directions and Operation

1. Remove the filling chamber cap by turning it and pull it apart from the filling chamber.
2. Fill the filling chamber with finely grounded plant material. Put the cap back.
3. After filling the chamber with the plant material put it on the exhaust vent of the hot air generator and allow it to lock in place. Press the green button/switch labeled ‘Air’. Allow the substance to be pre-heated for a couple of seconds. This will heat the ingredients so that the vaporization process is smooth.
4. Remove the mouthpiece from the valve balloon.
5. Stretch the balloon tightly before you put the balloon on the filling chamber.
6. Cover the filling chamber with the valve balloon. Once it is properly locked in its place, the valve will open and the balloon will be filled with flavors and vapors.
7. Make sure that you do not overfill the balloon. Only fill so much that it lasts for about 10 minutes.
8. When the balloon is filled, switch off the air pump and remove the valve balloon together along with the filling chamber.
9. As you remove the balloon from the filling chamber, the valve will close automatically so that the vapors do not escape from the balloon.
10. Now carefully lock the mouthpiece into the balloon.
11. Put the mouthpiece to your mouth and gently start inhaling. Pressing the lips on the mouthpiece will open the valve and the vapors will come out for you to inhale. Removing the pressure from the mouthpiece will result in closing of the valve.
12. Pull the balloon tightly to empty it after inhaling all the vapors.

Cleaning And Maintenance
Clean the filling chamber with 90% alcohol solution. You can use the handle of the cleaning brush to push out the upper screen out. After this the cap cylinder should be pushed out of the cap housing. To disassemble the filling chamber, push out the lower screen from the chamber upwards out of the chamber housing. After pulling apart the various components, make sure that you properly clean them out. To assemble back the filling chamber, push the filling chamber from above into the chamber housing. Insert the 3 clips into the foot of the filling chamber housing and insert the filling chamber from above.

Cautions and Safety Tips

• Keep the unit out of the reach of children.
• The plate under the device should correspond to the supply mains at the place of installations.
• If there are certain problems during the whole process then immediately pull out the power connection cord and turn off the whole system.
• Avoid looping or folding the power cord and unwound it to its full length. Do not keep the unit or the power cord near liquids or sources of heat. Make sure that you do not damage the power cord.
• Avoid using multiple sockets or extension cables.
• The vaporizer should be set up on a steady and a dry surface and a place where the temperature does not drop below 5°C or 41°F. Never install the vaporizer in a damp room such as Bathroom, etc.
• Do not repair or carry the unit when it is plugged in.
• Pull the plug directly and not the power cable from the socket.
• Do not operate the device if the main cable is defective or damaged.
• Never leave the vaporizer unattended when it is being operated. Also switch the unit off when it is not in use. Turn off the sir pump.
• Make sure that the ventilation slots and the exhaust vents are fully exposed and not exposed or obstructed in any way.
• Touching the exhaust vent or the filling chamber when they are hot may cause burning.
• The filling chamber should be removed after filling the balloon. This is done so that the chamber does not overheat.
• Never put your body parts or other objects into the hot air jet.
• The vaporizer should only be cleaned with a dry cloth you can use a damp cloth for cleaning if need arises.
• Under no circumstances should you place the vaporizer in water or other liquids. Also avoid cleaning it with a direct water stream.

Volcano Vaporizer is one of the most efficient unit that is available today in the market. The vapors produced are devoid of impurities and contain flavored and aromatic plant substances. Vapors are produced at a particular temperature which does not let plant substance get burnt. Vaporization does not involve combustion or excessive carbonization as is the case with smoking. The process of vaporization is least harmful to the respiratory system and does not destroy the essential parts of the plants.

Following are the instructions that one should follow when using a Solid Valve Volcano Vaporizer -

• Remove the filling chamber and insert the filling with sufficient amount of herbs.
• Put in the filling chamber and lower the screen with the help of a pin. It will make the content of the filling chamber loosely fit between the screens. Make sure that the filling chamber touches the top edge of the filling chamber cylinder. Do not let the plant material bend or obstruct the screen.
• Now put the filling chamber on the exhaust vent of the Volcano Vaporizer. Push the green button with ‘Air’ written on it, to turn on the air pump. Before the vaporization procedure begins the grounded herbs have to be preheated for some seconds.
• Connect the balloon with the help of the valve that is attached to it to the filling chamber. Fix the valve on the filling chamber from above until both the gripping fixtures are engaged. The vapors of active ingredients will slowly fill the balloon.
• Fill the balloon with adequate amount. Do not let it overfill with vapors. The amount of vapors contained in the balloon should only be able to exhaust out within 10 minutes.
• Now detach the balloon from the filling chamber by pressing the grippers together. The valve closes automatically. This will prevent the vapors from escaping. Put the filling chamber on an insulated and heat-proof surface.
• After this connect the mouthpiece to the valve balloon and make sure that both the grippers are attached properly.
• Start inhaling by putting the mouthpiece to your lips, pressing your mouth against the mouthpiece. Pressuring the mouthpiece will make the valve open and let the vapors pass out from them. Removing the pressure from the grippers will make the valve close automatically, so that not even a small amount of vapors cannot be lost.
• After inhaling the content of the balloon, pull it tight to make it empty.

Solid Valve Vaporizer Cleaning and Maintenance
Cleaning and properly maintaining the parts of the vaporizer increases the efficiency of the vaporizer and is also very important for the purpose of hygiene. Clean the mouthpiece, filling chamber and valve with the help of spirit or ethyl alcohol with paper or cotton towels. Dish-washing liquid with warm water can also be used to cleanse the parts of the vaporizer. All three parts can be easily disassembled. Disassembling the parts will enable you to clean the parts thoroughly.
Sometimes a single vaporizer is used by more than one person, in these cases maintaining the hygiene is very important. Hence, clean the vaporizer regularly and replace the part which are no longer in working condition.

The Volatizer 3 vaporizer is not only a revolutionary but also an evolutionary vaporizer. Its efficiency and performance exceed others in terms of functionality and competence. Its easy to use design and cutting edge vaporization techniques give the vaporizer a definite edge over others. If it is pure and unsoiled phyto-inhalation that you want then that is what you will get with Volatizer Vaporizer 3. It will make you free from using water filled containers, balloons and hoses. The best thing about a Volatizer vaporizer is that it is the only vaporizer that is pocket-size, battery operated and rechargeable. Volatizer vaporizer is multipurpose in nature as it can be used in aromatherapy, medicinal herbs, essential oils or other herbal substances.

Following are the identifying components of a Volatizer Vaporizer.

1. Custom Lockable Case
2. Extra-ceramic vaporization chambers
3. Cleaning Kit

Using the Volatizer Vaporizer

The Volatizer Vaporizer has to be charged before it can be put to use. Plug the charger into a standard 120 AC outlet and insert the plug into the socket present at the back of the Volatizer Vaporizer. A red light will be displayed on the screen when the unit is being charged. Another red indicator under the display screen will be lit to indicate that the charger is connected and the charging is in process. When the battery is fully charged then a green light will be displayed on the screen. It is recommended that the charger should be kept plugged in over night to ensure a fully charged battery.
The usage of the unit determines how long will the battery last. If the unit is set at higher temperature and used frequently then obviously the vaporizer would be required to recharge sooner. When the battery is low, the res light under the display screen begins to wink and the unit also makes a beep sound. The whole unit will completely turn off when the battery is fully discharged. The turning off of the whole unit will erase the previous temperature settings and new temperature is required to be set, when used the next time.

Instructions

Before the instructions are stated, it is very important to note that the Volatizer 3 Vaporizer cannot be turned on unless the mouthpiece is extended and the covering over the vaporization chamber should be completely closed. This small but significant instruction should be followed very strictly. Slide the vaporization compartment cover upwards to load the Volatizer Chamber. After this insert the ceramic chamber into the vaporizer. Generally there are extra ceramic chambers provided with the vaporizer with mesh screens. The screen is basically to prevent the herbal substance from touching the heating elements or interfering with the other parts of the vaporization chambers. Using mesh lids is totally a user’s choice, many people avoid using the mesh screen because of inconvenience. If you do want to use the mesh screen then do not shake or turn the vaporizer upside down as it will make the herb or its debris fall out or spread in the upper screen.

1. Load the Volatizer Vaporizer with a very small amount of plant material or herbal substance in the ceramic vaporization chamber. You don’t have to finely grind the herbal substance only reduce it to the size of a herbal pellet. If you want to use an essential oil then put only a small drop of oil on the vaporization chamber.
2. Insert the chamber which is loaded with the constituent herb into the Volatizer 3 Vaporizer and make sure that the vaporization compartment cover completely closes the chamber.
3. Turn on the unit by pressing the Off/On button. Words and numbers will be displayed on the screen as soon as you switch on the unit. The first number that appears is the nominal or the actual temperature in degree Celsius in the vaporization chamber. Set the temperature that you want by pressing the temperature increase (left) or decrease (right) buttons which are located below the screen. Just press once to to go up or down one degree, or hold down for faster adjustment of the temperature setting. When the temperature is adjusted, ’set’ will appear on the screen along with a blue back-light. After it is turned on, the last temperature that is displayed after you have released the temperature increase or decrease button will be the preset temperature till the time you adjust it again.
4. Next turn on the heat button by pressing it, a red light will glow. This shows the heating element is on. The vaporization process only develops when you turn on the heating element.
5. As and when the vaporization chamber reaches the preset temperature, the heating element and the red indicator light turns off automatically. Start inhaling the vapor through the mouthpiece slowly and deeply for about 5-10 seconds. Hold the vapors inside your mouth and then slowly exhale them. The heat button should be kept pressed during inhalation in order to maintain the temperature that you set inside the vaporization chamber. You should also take note of one thing that when you draw cool air from the vaporization chamber, then the sensors installed inside the heating element will maintain the temperature that was set earlier. The user can see this process take place as when you start inhaling then the red light which earlier was shut off, will now be turned on. If you feel that the outside air is much cooler then set the temperature 10° or 20° higher than the outside temperature in order to compensate for the loss of heat.
6. The temperature that is optimal to vaporize the herb or some other botanical substance is 180°C-200°C. Adequate vaporization also depends on the moisture content present in the herbs. The quality of the herbs also influence the vapors formed thereafter. Potency and essences available in the herbal material are some of the other factors that can modify the quality of the vapors formed. Exceeding the temperature of 230°C can lead to burning of the plant material as in vaporization nominal provides maximum experience. However, the user can conduct experiments with the amount and temperature settings corresponding to your preferences. Variety in temperature settings will also yield optimal vapors. Always remember that herbs are very likely to get incinerated above the temperature of 235°C.
7. After using the unit, let it cool for sometime. Do not to attempt to take out the ceramic chamber immediately after using it since it can get extremely hot during the vaporization process. The heating temperature can reach up to 280°C and cause injury to skin if touched. The amount of time that you have to wait for the vaporizer to cool off is dependent on the temperature that you had set earlier. After the unit is warm to touch and has cooled off, only then remove it and blow out the residue that is left inside the chamber. If the constituent remains attached then scrape it off with the help of a brush or tweezers. In case you have used an essential oil then replace the cotton insert. It is recommended that you leave the Volatizer vaporizer to cool off after every use.
8. The required ‘buzz’ from inhaling vapors is also dependent on the number of inhalations that you take. This in turn is dependent on the number of essences and flavors that are present in a herb. Sometime, one can reach the required point within 2 draws and other times it may require multiple inhalations. The same can be said about temperature settings. The more variations you make in temperature settings, the more ranges you would have to choose from. It is all about finding your comfort level. Different herbs and oils have different vaporization temperatures, depending upon their chemical composition. Some oils such as camphor and mint vaporize at temperatures as low as 30°-60°C. However, in many other herbs, there will be ingredients which get vaporized only within the temperature range of 100°-150°C. Common medicinal herbs generally vaporize within the thermal range of 180°-210°C.
9. In order to intensify your vaporizing experience, you can try increasing the temperature but the vapors formed thus will depend on the type of ingredients that would be present in the herb.

Cleaning and Maintaining the Volatizer 3 Vaporizer
The Volatizer Vaporizer is a sensitive electronic device requires care like that of a digital camera or a cell phone. The foremost care one should take with regards to a Volatizer 3 Vaporizer is that it should never be immersed in water or any liquid and never be exposed to heat, cold or moisture. Rough handling of the unit can cause damage that may be permanent. Removable components and parts that are movable should never be operated forcefully.

The internal components such as the vaporization chamber and the internal screen can be cleaned by using a brush or a tweezers. You should make sure that the chamber is completely devoid of any herbal or botanical particle. A cotton swab can also be used to clean out the inner parts. The upper internal screens should be kept clean and absolutely free of material debris. The cleaning kit that is provided along with the vaporizer contains the necessary tools that might be needed to clean out the dirt form the vaporizers. Having a complicated digital circuitry, the vaporizer is a technically advanced device which should not be operated upon by yourself. Always call in a technician to repair the Volatizer 3 Vaporizer, never even take chances with amateurs.

Safety Tips

The Vaporization Chamber has to be completely closed for the heating element to start functioning.

The Vaporizer should be completely charged before it is used. The unit can be used even when it is being charged.

Disassembling your Volatizer Vaporizer yourself might lead to permanent damage. Do not drop or misuse the vaporizer.

Exposing the vaporizer to extreme conditions such as heat, cold or moisture can make it dysfunctional.

Always load a small amount of herbal substance into the vaporizer and never overload it. Also do not exceed 230°C.

You can use an alcohol wipe to clean the mouthpiece.

By retracting the mouthpiece and closing the cover over it after use will turn off the unit and also conserve battery.

Always use herbal substances or plant materials that you are acquainted which should not have any additives, contamination or pesticides.

Never use a vaporizer if our pregnant, ill or under a doctor’s observation.

Never allow children or even adolescents to handle the Volatizer Vaporizer.

In a 30 minute time period only one ceramic vaporization chamber of tobacco should be used.

Be cautious while using a Volatizer Vaporizer.

Volatizer Vaporizer is a device that has completely transformed vaporization experience for its users. The highly proficient and smokeless vaporizer extracts the essential elements from the herbal substance and leaves out the carcinogenic and harmful ingredients. Vaporizers have superseded cigarettes and other ways of inhaling essences from herbal substances as the latter lead to dangerous affects.

Instructions given below should be followed when using a Volatizer vaporizer.

1. Put only a drop of oil or very small amount of herbal substance on to the screen. Make sure that the herbs are finely grounded. An adequate extraction does not require a lot of substance to be vaporized.
2. Now fill half of the flask with water and insert the glass tube through the stopper. Place the tube arrangement carefully on the mouth of the flask.
3. Now position the screen in glass bowl and place the bowl into the glass bowl and glass tube.
4. Attach the breathing tube to the outlet that is present at the side of the flask put the vaporizer on preheat for 10-20 seconds.

After this, put the wand on top of the heating chamber and heat for about 3 seconds. Now slowly start inhaling as the herb is being heated simultaneously. As the substance is heated, it will start changing color. The plant material will change into a slight brown. The oil drop will vanish and white vapor will be formed. This means that the oil is vaporized. The time consumed in vaporizing an oil or a herb depends on its quality and the moisture content that is present inside. However, with regular practice, you will be able to get the perfect vapor in not time.

Cleaning and maintaining the vaporizer increases the efficiency of a vaporizer and should be religiously undertaken.

Vapolution is another Vaporizer that has acquired a lot of popularity among those who indulge in vaporization. A portable vaporizer that provides you with a healthy alternative to smoking. The vaporizer also warms the herbal substance and gives out the ingredients that are least harmful and do not cause any alarming side effects.

Follow the instructions below and be assured of an amazing experience

1. Put the herbal material at the end closest to the dimple in the straight bowl. Now attach the end that is far from the dimple to the tubing. The dimple acts like a screen. If there is some difficulty in fitting the bowl into the tubing then submerge it into the boiling water for 3-5 seconds. It will make the bowl easily slip into the boiling water.
2. Now slide the white retaining washer over the straight bowl, so that it touches the food-grade tubing.
3. After this, very carefully insert the bowl in the top of the vaporizer. The bowl will continue to slip through until it touches the bottom of the heater. The washer should be positioned in a way that it prevents the bowl from directly touching the bottom heater. There should be a gap of 1/4″ from the heater.
4. Now carefully plug in the cord to a power supply socket or car adapter or the optional battery pack. This cord should now be plugged into the power jack on the back of the vaporizer. The vaporizer now receiving power supply can be switched on.
5. Turn the switch on. A light will illuminate.
6. The Vaporizer has to be pre-heated for sometime. The lowest temperature of the Vapolution Vaporizer is at 6 O’clock and the highest is at 4 O’clock. After 5 minutes of pre-heating, turn the vaorizer to your preferred setting, usually the setting at 12 O’clock is recommended. One of the many advantages of a Vapolution Vaporizer is that it is designed to continue working for 8 hours without overheating or burning out. Experienced users leave the Vaporizer on at their preferred setting all the time.
7. It is a usually advised that you should finely grind the herbs before loading them into the bowl. However, in case of a Vapolution Vaporizer, instead of grinding break up the plant pods in 1-3 small pieces. Roll the pods between your fingers and mold them into a pellet. Gently put the vapor pellet into the bowl. Do not make the pellet too big as then it will hamper the airflow and a good vapor would not be possible. If the pellet is too small then there is a very likely chance that it will fall out. Although loading is a procedure that requires practice but once learned, the vapor formed would be close to perfection.
8. After loading the bowl, place the loaded material on top of the pre-heated vaporizer. Now slowly and steadily start drawing the vapors in. Keep on drawing the vapor until you are out of breath. Hold the vapor in and then exhale. A visible vapor will rise. Repeat this process for 3-7 times. The vapor produced also depends on the quality of your herbs and the temperature that you have set.

The safe zone on the vaporizer is the temperature setting at which rarely will the herbs burn. This safe zone is from 10 O’clock to 12 O’clock. A user should not divulge much from the safe zone temperature setting until he or she has acquired enough experience to handle higher temperature settings. The herbs change the their colors during the process of vaporization. It turns from golden to dark brown gradually and later if kept on heat for too long to a black pellet. It will turn black only on settings above 2 O’clock. This temperature can also cause vapor choke. Hence avoid this setting.

Blow through the tube for cleaning the vaporized herb. Keep the bowl into a receptacle and blow so that the residue gets collected into the receptacle and the tube becomes empty. Wait for 30 minutes to 1 minute for the bowl to cool.

Maintenance

Maintaining the Vaporizer is very significant and the efficiency of any vaporizer depends upon maintenance. Clean the bowls by submerging them into rubbing alcohol for 8-12 hours and rinse with warm water. After allowing the vaporizer to cool for 30 minutes and then put a Q-tip in rubbing alcohol and clean out the heater receptacle. You can repeat the procedure if necessary. A dry Q-tip should be used to clean out the residue that remains attached to it. The tube becomes yellow after use and hence should either be replaced or cut short. Maintaining the vaporizer is not as difficult as it might appear, only consistency is required. Consistent cleansing will lead to better and efficient performance of the Vaporizer. Also bear in mind that, never force the bowl into the vaporizer as it can lead to breaking of the glass heater.

Hot Box Vaporizer is one of the few revolutionary vaporizers that are present in the market, today. Its sophisticated structure helps it to extract the vital ingredients from the herbal substance and produce an essence and oil that is not only soothing but healthy as well. When attached with the aromatherapy attachment, the Hot Box vaporizer diffuses the calm flavor throughout the room.

Following are the instructions that are to be kept in mind, when using the Hot Box vaporizer.

1. Plug in the Hot Box Vaporizer (unit) cord into the socket and switch on the unit by turning on the button present on the cord and wait for the lamp to light.
2. It will take about 15 minutes for the vaporizer to reach its optimal temperature. The time consumed would be more if you are using extension cords. Make sure that you set up the system away from the reach of children.
3. Grind the herbs finely and properly.
4. Pack down the finely grounded substance into the Wand and onto the screen through the narrow end of the Upper Wand piece either with the end of the tubing or some utensil that will easily fit into the open end of the Wand. Make sure that the substance loaded into the wand is no more than 1/3 volume of the wand, up from the screen. Extra packing of material will only lead to charring or burning.
5. Holding the Wand against the tip of the glass heating element and inhale through the tube. Do not apply excessive pressure onto the glassware lest it may break. Using broken glassware will only lead to damaging of unit and may cause injury to you. It is always advisable to start drawing through the tube quickly and gradually slow down. Remember the slower you inhale, the higher the temperature of the air that would warm the material in the Wand.
6. Do not draw too much vapor at the same time, inhale at regular intervals instead of continuous. If you draw in too much then it may lead to coughing. In order to check whether the device is working properly, then see if you are able to exhale a clean and pure white cloud. Do not forget to mix the herbs during each draw for better quality of vapors. It is sometimes recommended that you put a drop or two of water in dry herbs. The intensity of the vapor depends upon the moisture content in the herbs. Lack of smell usually depicts a high quality of vapors.

The simple method will result in getting you the required buzz that you seek. Keep the unit clean and dust free, when not in use. A unit that is switched on, should not be kept unattended for a long time. Maintenance of the vaporizer is very important, it can increase the efficiency of a vaporizer. Firstly, you should keep a check on the power cord and make sure that it is not damaged in anyway. Replacement of different components of a vaporizer depends on the frequency of usage. The screen can be replaced by a 5/8″ screen in the Wand.

To replace the screen the following steps should be followed:

• Pull apart the two parts of the Wand (Upper and Lower)
• From the upper part, push out the screen
• Place the new 5/8″ screen from the bottom end of the Upper piece of Wand.
• By rolling back the O-ring onto the upper part of Lower piece of Wand, connect the lower and upper Wand pieces.

Clean the tubing by running it under hot water and using a skewer to scrape out the inner wall. It is suggested that you replace the tubing every 2-3 months. The Wand should be thoroughly cleansed especially when it becomes brown due to usage. In this case, pull the Wand apart and scrape it clean by using a skewer or some other tool. You can also run the Wand under hot water, if the material is difficult to remove.

The Vapir Vaporizer is another easy to use, state-of-the-art vaporizer with all the component of a standard vaporizer as well as some other advanced features. It has a mouthpiece, heating chamber, a protective heating shield, LCD display, power input, temperature regulator, LED light, Tube, X-tube, rechargeable battery and a charger (optional). It is a very handy vaporizer without any additional and highly complicated parts that hinder rather than assist in the vaporization experience.

Following are the instructions that should be carried out when using a Vapir Vaporizer.

1. Grind your favorite herbs very finely and reduced the plant material almost to powder form.
2. Now preheat the unit to the recommended temperature that of 360°/192°F to 375°/207°C.
3. Set the required temperature by using the temperature regulator system which can be used to increase or decrease the temperature. Setting the temperature to an optimal figure requires a lot of time and is also specific to the herbs that are being vaporized. If you are not getting enough vapors then turning temperature up is advised otherwise lower down the temperature.
4. Next step is to unscrew the mouthpiece and adjust the temperature that you desire. Press the heat button to activate the heating mechanism. LED will start glowing showing that the heat is being utilized and warming up the unit. Temperature that is displayed first on the screen will be the set temperature and then the actual temperature.
5. After the unit has been preheated, put the herbs into the chamber. Make sure that you do not touch the unit under any circumstances as it is very hot. Never touch near or inside the unit, when it is hot.
6. Only fill half of the unit and never full. Overloading will result in obstructing of the vapor formation.
7. Turn the mouthpiece clockwise while attaching it to the unit.
8. Now simply start inhaling the vapors from the tube, slowly and deeply. Enjoy the flavors and essences through the vapors. Do not inhale directly through the mouthpiece as the unit is very hot and might injure your lips or other parts.
9. Make sure that you soak up the tube in warm water to boil the tube and hence clean it.
10. After using the unit, clean off the herbs by using to spoon that is included in the purchase package. Do not damage the internal mesh while cleaning the residue.

Charging the Battery

• To charge the battery connect the battery to the unit and uses following the instructions given above.
• The battery should be charged for at least 8-12 hours to charge it fully. For first use, charge the battery for full one night or no less than 12 hours. A fully charged battery will last for 1 full hour of continuous heating. It is not at all advisable to charge the battery for 24 hours.
• A 12V car adapter can also be used to charge the battery of the Vapir Vaporizer. For this, all you have to do is attach the car battery to the unit. However, do not use this device or any other aroma therapy device while driving or operating heavy machinery.

If you go step by step according to the directions, you will be able to achieve the optimal vaporization experience and enjoy ecstatic flavors and essences in no time.

Herbal Aire vaporizers help users to inhale their favorite herbal substance without burning the material into ashes and releasing harmful chemicals such as tobacco and other carcinogenic elements. It also assists in direct inhalation providing soothing flavored and aromatic experience. It can be used without extensions. The Bag Fill allows you to extract even the spent herb. This Bag kit fill system makes the vaporizer much more beneficial, productive and efficient. When using the Herbal Air, make sure that you follow the instructions given below.

Its easy to use components and state-of-the-art set-ups helps the user to easily obtain the perfect vaporization experience. Such as, temperature control board with temperatures between 250°F– 400ºF or 125ºC –200ºC, tri-colored temperature light which inform when the required temperature is reached. HerbalAire also has an automatic shut off system, which shuts it off, when it has not been in use for 30 minutes or so. Not to forget the vaporizers, highly advanced dual functionality which allows it to be used as a direct inhalation unit or attach the pump fill bags with cool potent vapor. The 12ft cord that comes along with, gives it an advantage of using it conveniently. Its teflon mouth piece and sophisticated exterior made of glass and nylon gives it a smart look as well.

Instructions

1. The first step involves the plugging-in of the Herbal Aire. The unit comes with a 12 feet cord. Switch on the power that is present on the power cord.
2. Next load the bowl with finely grounded herbal substance. One end of the tubing fits into the back of the pump and the other has a connector that attaches to the back of the HerbalAire. Do not overload the bowl with the substance.
3. Set the temperature to an optimum degree and let the material warm up. Once the vapor start coming out of the mouthpiece, inhale them directly out of the tube or connect the bag and let vapors collect in the bag. The bag would be filled with flavored essences ready to give you the desired buzz.
4. After use, unplug the HerbalAire and let it cool for a suitable duration of time.

One of the great benefits of using a HerbalAire is that the air jets permeate through the herbal substance when a user turns on the pump for the bag fill kit. At other times, the herb sits not utilized, preserving all its essences and flavors. Vaporizer also extracts the active ingredients at lowest temperatures with maximum efficiency, without losing any of the relevant ingredient.

Cleaning the HerbalAire
Ensure that you take care of the HerbalAire and clean it regularly. Maintenance helps in increasing the efficiency of every vaporizer and HerbalAire is no different. Clean the crucible and the core with damp cotton or a paper towel. The inside of the core should also be properly cleaned.

Ethyl Alcohol can also be used to clean the unit. Make sure that no liquids get poured into the core, not even a trickle.Teflon pieces can be removed and should be rinsed under water. If build up occurs then scrubbing or dish soap may be used. Carefully handle the screen inside the mouthpiece and the crucibles. The body of the HerbalAire can be cleaned with a damp cloth, never immerse the HerbalAire in water or other liquids.

Clean the mouthpiece and screen either with water or ethyl alcohol. Store the components properly putting them back into the plastic storage. In case of damage to a component, get it replaced. Tubing and screens are available at any hardware store.

Vaporizers have made the life of those who indulge in vaporization, very easy. Not only does vaporization prevents cancer and other disease that are caused by smoking, but also helps people get the needed buzz by utilizing advanced technology. Most of the latest vaporizers come with state-of-the-art functions that tell the user, when it is safe to use the vaporizer and when it is time to turn off. In order to use the vaporizer efficiently, one should thoroughly read the instructions and use it accordingly. Sometimes the vaporizers are preset to temperature between 200˚F and 375˚F.

Following are the instructions that should be kept in mind while using a vaporizer. These are given to simplify the use for the individual.

1.  Heat up the vaporizer for 2 minutes and wait for the LED to turn on but will glow in different colors. The fan will start when the desired temperature is reached. Meanwhile, insert the tubing into glass vapor whip and load the herbal substance.
2.  Make sure that the substance is finely grounded. Do not overload the glass bowl and put only 1/3 of the clear glass chamber above the screen.
3. Inhale from your mouth piece into the glass whip and creating a vacuum, suck up the material to be vaporized, insert glass whip in the glowing heating chamber and start inhaling deep and slow for at least 10 seconds.
4.  Start inhaling quickly and keep steady for about 8 seconds or until desired flavored is achieved. Adjustment of temperature is only required if there is some amount of moisture content in the herbal material.

If the vapor that you are getting is either too weak or too harsh then you need to adjust the temperature of your unit. In order to do this, adjust the temperature on your vaporizer by holding the button P until SP starts flashing. To adjust the temperature, press and hold the up button for stronger vapors and their increased densities. Hold the down button for obtaining lighter vapors.

When the material is thoroughly vaporized then it will turn tan but never dark or burnt. After using, blow out the residue in a waste basket and switch off the whole unit by turning off the power button. The fans will automatically switch off after it has reached a cool temperature. The Stealth will also shut off on its own and next time you want to use it, simply turn the power on and wait for LED light and fans to come on. Insert your loaded whip and enjoy using the vaporizer by following the instructions given above.

Clean the glass whip very often by dipping it in 90% USP rubbing alcohol, rinse with fresh water and blow dry. If the screen cannot be used then replace it with a new one. Screen or a tube can be easily bought from a hardware store.

Safety Tips

1.  Always place the whole unit on a non-combustible surface. It should also be taken into consideration that the outlets for air and fans should not be blocked from any side in order to prevent heating up unnecessarily.
2.  Never use it around children .
3.  Always shut down the whole unit, when not in use. Prolonged heating up of the vaporizer may cause damage to is system and may also cause injuries to the person using it.
4.  It is not advisable to leave the unit unattended while it is on. Always make sure that it is switched off before you head for something new.
5. Never exhale or insert any foreign object into the heat chamber. Also never put your finger inside the heating glass chamber tube, this will result in damage to both the component and to you as well. Turn the unit off, quickly if it happens accidentally, let the vaporizer cool off for a while. After the unit has cooled off, only then unplug it and move it around. Wipe the front and back of the unit with an air duster and practice the cleaning routine more regularly by blowing clean air into front and back of the unit.
6. Keep the vaporizer as dust free as possible.

To use Vapor box for a completely exciting vaporization experience, one has to be aware of the best way to use it. Following are the necessary instructions that a user should follow in order to get the perfect puff.

1. Firstly, turn the heat knob to 12 O’ Clock and let the vapor box heat up for 5 minutes.

2. Crush the material very finely and put it into the glass bowl. Suck into the glass hand-piece by inhaling on the mouthpiece. Do not overload, only put about 1/3 or less of the volume of bowl. It should just touch the screen.

3. Next, touch the Pyrex tip to the glass slipper that covers the iron, holding it there, take steady puffs and simultaneously release the Pyrex tip from the point. This will clear the tube. Make sure that you do not draw too slowly because if the iron is too hot, it will make substance catch fire. If such a situation arises then quickly turn down the temperature and repack with fresh material. You can change various settings to find a suitable temperature and ideal speed for drawing puffs.

4. Always check the material, after you have taken in a draw. If it is darkened or blackened, then turn down the temperature by turning the knob or start inhaling faster. If a puff isn’t coming then increase the temperature or start inhaling slowly. The puff might not produce the same strong sensation and may even be very light. This is because the essence might have slipped into a thin and cool oil mist, which is only visible under a light source. However, certain people prefer a very strong, full-bodied, smoky puff. If you continue smoking, then you will notice that the herbal essence has deprecated into a thin mist. From here there is no point of extracting the smoke through worn out material but better to prepare for the next exciting vaporizing experience.

5. Dispose off the material that is present in the hand-piece into a bottle or a plastic container. If some residue still remains in the tip, expel it using the stir tool.

Stirring between puffs, distributing heat evenly and equally, rotating the bowl or the chamber, adopting different speeds and rates of inhaling and experimenting, can actually accentuate your vaporizing experience. So try different things while vaporizing but not too radical. Moisture content in the substance, size of the material and length of the glass bowl and tube are some of the other factors that influence vaporization.

Maintenance

It is very important to clean the various components of a Vapor Box, vaporizer. This practice helps in the maintenance of the vaporizer. The three basic parts that should be focused upon are glass, tube and screen. All these parts should be pulled apart from each other and cleaned. In the Deluxe Model, the screen can be unscrewed from the metal top piece. For those having the old Model Hand-piece gently push up the screen of the top end using an unfolded paper clip from the bottom end.

If your screen has completely worn out or the tube has depleted then they can be purchased from a hardware store. For the screen, make sure you buy a thin gauge screen and for the tube the inner diameter should be 7/16” and the outer should be 5/16”. Other sizes that perfectly make an airtight seal with the glass will do just fine. If the tube does not fit into the glass then run it under hot water for 30 seconds to make it flexible, which occurs due to softening of the vinyl.

Following are the instructions one should adhere to in order to get an exhilarating experience. With the advanced Vapor Tower, your definition of vaporization will completely change.

1. Turn the knob to 12 Noon upto 5 minutes to heat the Vapor Tower. Keep in mind that the heater is very powerful and you should never use vaporizers at high temperatures if you are not experienced. The heater is powerful enough to burn your material and even your lungs!
2. Finely grind the material to get the best results. Turn the Vapor Tower glass hand-kit to load the herbal substance into the metal fitting of the bowl. Never overfill the chamber and only load it enough that it is just from the covering of the screen.
3. Cautiously put the hand-kit back together and avoid any spilling of the herbal material. If the hand-kit is fully loaded then do not screw it completely, but if it is loaded lightly then fit it completely.
4. Now insert the hand-kit back to the Vapor Tower and start by puffing fast and slow. It is important to begin fast but gradually slow down the rate of inhalation as it will help you draw hotter and stronger puffs. For every fast toke, take a short and slow puff. Keep on innovating with the method and changing the knob until you find the most suitable temperature and your ideal puff range.
5. Now very carefully remove the hand-kit and look into the material. If the material is blackened then turn the knob or start drawing faster. The glass and the metal parts would be very hot, so be extra careful in handling the apparatus. If you still do not get a swoop of air, then turn up temperature a little and draw in very slowly. It may not appear as if you have got a puff as by now it must have dissipated to a cool clear oil mist, which is only seen when blown against a light source. After constantly using the vapor tower, you would notice that material has exhausted and has become devoid off its essential oils.
6. Unscrew the hand-kit, after all the material has been utilized. Expel the resin or the residue of the substance by turning the bowl upside down. You can also use the stir instrument to scrape off the material that is stuck to the sides. Be careful not to lose the silicone rubber O-ring or screen.

Maintaining a Vapor Tower

It does not involve any elaborate procedures. One only has to pull glass, screen and the tubing apart to clean them separately. To clean the screen, one has to hold it over a flame and burn off all the residue that is left on it. For the glass, if there is a buildup, then only put the hand-piece in alcohol overnight. The silicone tubing can be washed under hot water or purchased from a hardware store of size 7/16” inner diameter and 5/6” outer diameter. Other sizes that easily fit and make an air tight seal with the glass would also be fine.

Step 1
Let the Vaporizer heat for 3-10 minutes by turning the heating element Depending on your personal requirements and preference, turn back about 1/8. Simultaneously prepare your herbal mixture, which should be fine as possible, in order to get the best results.

Step 2
Pulverize the material and put it into the bowl. Do not stuff more material than it can hold. It should be approximately 1/3of the bowl volume. Pack down the material using a pen or a pencil. If you overload it then it will obstruct the airflow, leading to overcooked or even burned bowls. Suck up from the tip of the glass hand-piece by inhaling from the tube.

Step 3
Next step is to check the iron, which should have a dim red glow. If it has some other glow other than dim red glow, like a bright orange then turn the Vaporizer off for 10 seconds and reset the maximum until the glow dims to a dull red. Now touch the pyrex tip to the glass slipper covering the iron. Holding it there, steadily release the pyrex tip from the element, so as to clear the tube. However, be very careful about how slow or fast you draw because if you are drawing too slow or the iron is too hot, then the material may catch fire. If it happens then blow out quickly and re-arrange with fresh material.

In order to get a proper kind of ‘high’ or ‘buzz’, it is important to note the color changes of the content in the glass slipper. If you are not getting a proper hit, then turn the knob down or start drawing a little faster. The smoky hits and the buzz depends on the preference of the people, so they arrange the set up accordingly. If the material is exhausting then it will indicate by decreasing into a thin blue disappearing smoke. This means that the essential components of the oil or the herbal substances have been exhausted. It is advised that the material you use is dried and not moist, as then it may not work as efficiently.

Step 4
To get a quick hot air vaporization, carefully slide the bowl over the heating element and start inhaling through the whip. Turn off the unit, when finished.

Use the vaporizer properly and enjoy the perfect vaporization experience.

Due to the health benefits and protection from the dangers of smoking, vaporization has become immensely popular among people. It is the process by which active ingredients of a herbal substance are released by application of low temperature heat without burning the herbs. This procedure leads to a cleaner, healthier and unadulterated effect, devoid of carbon monoxide and tar, which are carcinogenic in nature.

Following are 10 easy steps that will enable you to operate the Trifold Vapor Tower.

Step 1
Heat up the 5 Vapor Tower, after turning it on for 5 minutes and set the dial around 12 O’clock.
Step 2
After this read the instructions manual and arrange the apparatus and substance accordingly.
Step 3
Now, very carefully open the bowl and put it on a solid surface with the glass side down.
Step 4
Grind the herbal substance forcefully and vigorously for some seconds.
Step 5
After grinding the material and making sure that it is perfectly amorphous, pour it on a business card. Then fold the card to put the material in the bowl.
Step 6
The material should just fill the bowl, do not overload. The screen should smoothly layer the substance.
Step 7
Hold the rubber insulation of the bowl and properly screw the handkit back on the bowl, carefully.
Step 8
Cautiously slide the handkit on the heater in the Vapor Tower.
Step 9
Now, the actual vaporization begins. Start with both short and fast puffs so as to get accustomed to the vapors. Be careful that you do not inhale a lot in the first go. It is important that you find your comfort level by alternating breathing speeds and durations. Accordingly increase the intensity of the heat, set it to 1 O’clock and wait sometime for stronger vapors.
Step 10
Once you have had your fill, carefully remove the handkit from the Vapor Tower. The glass bowl will be extremely hot and hence , let it cool for sometime and maneuver it by holding the rubber insulation only. Dispose the used substance and repeat the process as needed.

Vapman is a stylish, portable and an easy to use vaporizer that is made from high quality European components. The device is regarded as one of the best portable vaporizers that are available in the market today. Vapman is small in size and can easily be carried anywhere. A pre-filled butane torch lighter is also provided along with the unit for the convenience of the user. Vapman further enhances vaporizing experience by giving the user, the liberty to carry the vaporizer from one place to another. Vapman is indeed an advantageous product!

Using a Vapman is very simple. Follow the instructions written below and enjoy!

1. In order to load the Vapman vaporizer remove the cap by turning in the anti-clockwise direction.
2. Fill the pan with finely chopped herbs up to the rim. Remember not to overload as it may hamper circulation of air. After loading, put on the funnel tube.
3. Now hold the Vapman by its wooden casing and tilt in a way that the flame from the lighter points exactly towards the apex of the copper pan. The time taken to heat the pan depends on the intensity and length of the flame that is being used. If the flame is long then keep the duration small and if it is short then keep it for a longer time. Heat the vaporizer twice between intervals for uniform heating. However, do this till the time, the copper pan is cold.
4. Start inhaling very gently and deeply after heating for sometime. Inhale for about 5 to 15 seconds and then hold the herbal vapors in your lungs for a while before exhaling.
5. Heat the vaporizer once during further inhalations. As the pan will already be warm from previous hating, make sure that you do not over heat it and end up having burnt out herbs. If the herbs turn dark or black in color then do not inhale as it will be harmful to your lungs.
6. When no vapors are produced then it means that the whole of the herbal substance has been used. The residue left will be brown in color.
7. Remove the Funnel tube and the cap and clean out the herbs with the help of a toothpick or needle. Do not let the substance clog the air nozzles.
8. It is advised that you rub the aluminum strainer well with the material or a paper towel. The aluminum stainer should always be clean. if you rub the strainer when it is warm then the residue will come off easily.

Cleaning and Maintenance
Make sure that the aluminum strainer, air holes on the cap, and the air nozzles should be clogged. Cleaning the residue off can be accomplished with the help of a needle or a toothpick. Clean the mouthpiece with alcohol or hot water. Regularly, take out the aluminum strainer and clean it with alcohol. The wooden cone will collect the residue that has been scraped off. Keep the wooden cap and mouthpiece into acetone for cleansing.

Points to remember

• A Vapman only works with a jet-flame lighter.
• Wooden casing is provided so as to avoid any burning that might be caused.
• Herbs will burn if exposed to heat for a long time
• The Vapman is fully functional even without the coating. When the copper bowl gets overheated (600°C or 1100°F) then the gold coating will scrape off.

Vapor Genie is an incredible device which is very easy to use. It provides users the ultimate vaporization experience. The vaporizer pipe is specially designed for the user to inhale natural ingredients without having to worry about the harmful components of the herb that might be dangerous to the user. The Vapor Genie gently warms the herbal substance without burning it and thus resulting in a fragrant and flavored vapor for the user to inhale.

Following are the instruction that you should follow while using the Vapor Genie.

1. Finely shred the tobacco and sprinkle it loosely on the bowl. If you pack the tobacco tightly then it may cause trouble as shredded tobacco has more surface area that aids the vaporization process. Also overloading the bowl can cause burning.
2. Now connect the flame filter onto the bowl by screwing it. However, be careful that you do not screw it too tightly.
3. Next step is to supply flames to the flame filter. As you supply the flames make sure that you are simultaneously inhaling the vapors. A conventional 1 inch lighter flame is perfectly suitable for the Vapor Genie. To heat the vaporizer uniformly make sure that you move the flame around. Using a bigger lighter might help. Be careful that you don not touch the ceramic filter as it will create soot which can clutter the filter and give you a bad taste.
4. Remember to inhale slowly and steadily if the flame is small. If the flame is large then inhale a little faster.
5. The temperature can be regulated by balancing the rate of inhalation with the intensity of the flame that is being supplied to the vaporizer. Increase the temperature by providing a larger flame and for decreasing the temperature supply a small flame. If you inhale slowly then the temperature will of the vaporizer will become high.
6. The best way to judge the quality of vapors that you inhale is to concentrate on the flavor and the sensations that you are experiencing. Accordingly you can adjust the flame application that you have been applying. Also exhale in between. A bluish colored vapor will be expelled out, which is normal.
7. Do not forget to stir and rearrange the tobacco during inhalation. A small amount of tar might be produced in the end, or debris might be informed. Frequently clean out the debris from the screen and the bowl.

How to Maintain the Vapor Genie
Always take care that the flame never reaches the ceramic filter. It can lead to deposition of soot on the bowl and the ceramic filter. However, soot if deposited can be removed by pouring hot boiling water onto the ceramic filter. Keep pouring the water until no soot remains. Other option is to burn off the soot using a blue flame windproof lighter. To clean out the soot, direct the flame towards the soot deposits and suck the air through the filter. The filter can be heated till 30-60 seconds. Another caution that one needs to undertake is that of not screwing the filter too tightly! It might damage your Vapor Genie.

Enjoy and puff away with the Vapor Genie in a healthy way.