Instructions For Use
HERB TUBE ATTACHMENT
For best taste, we recommend following the procedure below to eliminate any
plastic tastes:
- Soak tube in warm-hot (not boiling!) water for 30 minutes. Tip: Add
essential oils to water for better taste.
- Remove cap by twisting top portion of unit and flipping cap over.
Insert warm tube through back of cap.
- Insert tube through top of unit. You do not need to
remove the cap to do this but you can remove the cap
if you like.
Optional tube attachment is for flavor delivery purposes. Never put your mouth to
outlet valve. It may be hot. Always either use a tube or taste flavor from a distance
of several centimeters without touching the outlet valve.
Before using this unit for the first time, run it on maximum temperature and the
maximum fan speed for 2 cycles (20 minutes). This will help further eliminate any
unwanted smells from the manufacturing process.
- Insert tube before use.
Grind herbs in our Element™, Max™ or Maxine™ Herb Grinders
(sold separately) or in a coffee grinder.
- Preheat Vapormatic Deluxe™ to 300*F/149*C with the drawer
out. Wait for the light to turn green, then insert the disk drive.
- Inhale the flavor immediately upon insertion.
- When inhaling, breathe deeply. Hold the vapor in. Repeat for
10-15 minutes.
- Remember, visible vapors will not always be present.
Instructions For Balloon Inflation Kit
CUT THE TUBE TO 3” INCHES - 4” INCHES FOR BEST RESULTS
WHEN USING WITH THE BALLOON.
This Vapormatic Deluxe Vaporizer is equipped with a new supercharged heater.
Changing the fan speed may or may not noticeably affect the temperature. It
is not necessary to heat up your unit to the maximum temperature to inflate
balloons. Please use a moderate temperature between 120C/250F and 176C/350F
when preheating your unit. Using a higher temperature may cause burning of
your herbs.
When using a higher temperature we advise the use of a higher fan speed for
optimal vaporization.
FAN SPEED SETTING
HIGH= 1-10 MEDIUM = 10-15 LOW = 15-25
FOR EFFECTIVE BALLOON INFLATION:
- Preheat the unit to the desired temperature .
- Connect balloon with tube attached to the vapor outlet valve.
- Insert disc and set the fan to a high speed.
- Prepare a second balloon so you can place it directly on the valve when the
first one is filled.
- Repeat filling balloons until flavor has diminished.
NOTE
The quantity of balloons you inflate with vapor
from one filled disc will depend on many factors
including the condition of your herbs.
- Most vapors are invisible. As long as there is a
flavor, there is vapor.
IMPORTANT INSTRUCTIONS
IMPORTANT OPERATING INSTRUCTIONS FOR VAPORMATIC
DELUXE ™ VAPORIZER SUPERCHARGED FAN MODELS
DUE TO HIGH AIR PRESSURE, TEMPERATURES MAY FLUCTUATE
SEVERAL DEGREES CAUSING THE GREEN LIGHT TO FLICKER BETWEEN
RED AND GREEN. THIS IS NORMAL.
FAN SPEED SETTING
HIGH= 1-10 MEDIUM = 10-15 LOW = 15-25
It is imperative that you place your Vaporizer’s fan setting on the HIGH or
H position when starting it up. Failure to do this may cause damage to your
Vaporizer that is not covered under warranty. This vaporizer has multiple fan
speed settings: L for LOW, M for MEDIUM and H for HIGH. The unit should always
be started on H for HIGH so that it can properly achieve the speed it requires. The
unit might not operate properly if it is not started on the HIGH position. If the unit
is heated without the fan on, it could possibly overheat and cause damage to the
unit that is not covered by the warranty. In the event that this occurs, immediately
turn it off and restart on HIGH.
If your fan ever turns off or you notice it is not on, immediately turn the unit to the
off position, adjust the fan speed to H (HIGH position), and turn the unit on with
the heat off (heat is the large button with a flame on it). Do this for 5 minutes. It
should cool your device for usage.
Never unplug or turn your unit off until it has had sufficient time to cool down.
Always leave the fan running without heat for a minimum of 5 minutes after
each use.
As a safety precaution, your unit is equipped with an internal safety switch. This
switch will disable your unit should it ever overheat. If your unit malfunctions or
stops heating, leave the fan on H (High position) for 20 minutes to cool the unit
down. Then, turn your unit off. At this time, it is safe to either restart the unit or
unplug it and store.
Always unplug the unit from the electrical outlet before cleaning. Never turn on
a wet unit. Always make sure your unit is completely dry before turning it on. Do
not attempt any repairs to your unit as doing so may cause fatal injury or void
your warranty.
LEAVE FAN ON WITH THE HEAT OFF FOR 2-5 MINUTES AFTER USE.
THIS WILL COOL THE UNIT AND PREVENT DAMAGE CAUSED BY
HEAT. NEVER STORE A HOT UNIT.
-
This unit and many of its components get very hot! Read all directions and
heed all cautions carefully before using this device. Serious injury may result from
improper operation.
- Optional tube attachment is for flavor delivery purposes. Never put your mouth
to outlet valve. It may be hot. Always either use a tube or taste flavor from a
distance of several centimeters without touching the outlet valve.
- Never cover air intake valves. This may cause the unit to overheat and
malfunction.
- This unit has a preset safety time of 10 minutes. After 10 minutes of operation,
the unit will turn off to avoid overheating and to prevent any accidental damage
to the unit by leaving it on inadvertently. After 10 minutes, you can manually reset
the unit for up to another 10 minutes.
- Visible vapor will not always be present. Vapor is very different from smoke.
Even in the absence of visible vapor, the unit is still emitting potent vapors. The
vapor emitted after you first insert your drive is some of the most flavorful and
most beneficial vapor in your entire session, regardless of the fact that it may be
mostly invisible.
- The Vapormatic Deluxe ™ comes in both 110v and 220v versions. Check rating
label before use to make sure it matches your country’s voltage.
WARRANTY
You must register your product either by mail or on our site within 15 days of
purchase for warranty to be valid (except where prohibited by law*). Warranty
covers defects in materials and workmanship which occur with normal use of the
device and when device has been purchased from an authorized retailer. Warranty
valid for original buyer when registered within 15 days from purchase. Limitations
and restrictions apply.
*Some states do not allow the exclusion or limitation of incidental or consequential
damages or limitations based on the duration of an implied warranty. The
limitations and exclusions written above may not apply to you. This warranty gives
you specific legal rights, and you may have additional rights based on your state
law. Other restrictions may apply.
For more information, helpful tips and hints, and frequently asked
questions please visit www.vapornation.com |